Stenhoj Lift Installation Manual

1. Stenhoj Lift Installation Manual Diagram
2. Stenhoj Lift Installation Manual Pdf
3. Stenhoj Lift Installation Manual
4. Stenhoj Lift Installation Manual Download

Stenhoj Lift Manual - Faculdadedeengenharia.com The Stenhoj parts needed to get lifts up and running again. Ben Pearson Parts Autolifters.

1. Warning: This manual does not cover the procedure for disenabling the entire plant. It contains only instructions relati.
2. Download stenhoj repair manual instruction for Android on b.bakcister.site.

INSTALLATION

FRONT IMPLEMENT

KIT

INSTRUCTIONS

MFG. NO. 1691195

A

WARNING

Stop the engine and remove key before

installing kit or making any adjustments.

NOTE: For tractor Mfg. No. 1691017 with serial num-
ber 1273 or lower, and tractor Mfg. No. 1601019 with
serial number 10400 and lower, it will be necessary to
replace the existing bracket support with part number

1676455 in order to install this kit.

NOTE: Make sure

hydraulic wnnections are tight.

Where possible make connections using a vise before

installing parts on tractor.

Check kit parts against illustration and parts list on

pages 2 3.

2. Remove tractor hood to ease installation.

3.. See Figure 3. Remove the existing retaining rings.

Install the bushing (4) and lever (3). Install the curved

washers and retaining rings.

4. Disconnect hoses from existing valve. Note and mark

their positions. Remove the valve by removing nut

and bolt that holds the hydro fill tube.

5. Install the new valve using existing hardware and

new

x 2

(28, figure 3). This longer

also secures hydro fill tube clamp. Use the

upper hole in the mounting plate for the new
screw as shown.

6. See figure 1. Connect the hoses to the new valve in

the same positions as on original valve. Connect the

right and left tubes (5 6, figure 3) as shown.

7, Route the front tubes (9 10, figure 3) under the

front brackets as shown in figure 2.

6. See figure 4. Assemble the plastic plugs

retain-

ing rings

bodies (14) and brackets (15 16).

Attach to tractor as shown in figure 3.

9. On right-hand side,

bracket (16, figure 3)

using

lockwasher (20) and nut (21).

On left-hand side, secure bracket (15) using same
hardware used to secure bracket for PTO idler
spring.

The PTO spring is under tension when

Installed.

Figure 1.

A. Lift Lever Support

E. Hose

E-Ring

F. Elbow

C. Tube, Right (Ref. E,

D. Tube, Left, (Ref.

Fig. 1)

Figure 2. (Hood Removed)

A. Brackets

Figure 3.

A. Plugs

Brackets

FORM 1701802

The Chamberlain Group, Inc.

A DUCHOSSOIS ENTERPRISE

© 845 Larch Avenue

Elmhurst, Illinois 60126

Stenhoj Lift Installation Manual Diagram

OWNER'S MANUAL

MODEL GJR/HJR

WALL MOUNTED STARTER

ADDENDUM

Refer to Model GJ or HJ

Installation Instructions

PHYSICAL MOUNTING DIMENSIONS - MODEL GJR

4 3/4'

B

A

7 3/8'

PHYSICAL MOUNTING DIMENSIONS - MODEL HJR

ELECTRICAL ENCLOSURE WALL MOUNTED

STARTER MODELS HJR/GJR

6 13/16'

13 1/2'

Important Notes

Stenhoj Lift Installation Manual Pdf

Please Read Before Proceeding

1.Make sure that the serial number on the operator limit switch cover matches the serial number on the electrical enclosure cover.

2.All field installed wiring must be run using U.L. listed conduit and connectors.

3.Install high voltage wiring and 24VAC (control and limit) wiring in separate conduits.

Installation

1.Install the operator motor and frame assembly according to the Owner's Manual for your model operator, (either GJ or HJ).

Stenhoj Lift Installation Manual

2.Securely attach the electrical enclosure to the wall adjacent to and within sight of the door and operator. See Figure 1.

Stenhoj Lift Installation Manual Download

3.Refer to Figure 1 and wiring diagrams for locations of conduit and wiring connections.